Cut and Shoot, TX Permit Fees (2026)

Building permit fees and building, electrical, plumbing, mechanical/HVAC, and roofing permit fees for Cut and Shoot, straight from the official fee schedule, with a free permit fee calculator below.

Residential remodels and additions need no city building permit, so no estimate is shown for them. Work started without a permit pays double the permit fee. Commercial work of $50,000 or more also registers with the Texas Department of Licensing and Regulation (fee paid to the state).

Roofing Permit

2 county-assigned inspections

Open in calculator

Plumbing Permit

$220.00

2 county-assigned inspections

Open in calculator

In Cut and Shoot, a $20,000 re-roof runs $110.00 in permit fees, a $10,000 HVAC change-out $220.00, an electrical panel upgrade or rewire $220.00, and a whole-house repipe $220.00. Totals include the documented surcharges and minimum fees; where the schedule prices by unit, figures assume 2 county-assigned inspections. Each figure is that single permit only: a job that combines trades, like a kitchen remodel with electrical and plumbing work, pays each applicable permit. Pick a project to load it in the calculator below.

Jump to Permit Fee Calculator

Source

City of Cut and Shoot Ordinance No. 135, Municipal Building Permit Inspection-Plan Review Fee Schedule (Exhibits A and B)

Covers building, electrical, plumbing, mechanical/HVAC, and roofing permits.

Official Fee Schedule

Call the building department at (936) 264-3100.

How Cut and Shoot values a job: Commercial valuation follows the ICC Building Valuation Data table (August 2012) for new buildings and additions, and project valuation for alterations and build-outs, as determined by the building official.

Schedule effective April 29, 2021. Last verified: November 3, 2026

Cut and Shoot Permit Fee Schedule

Every documented rule for each permit type, straight from the official schedule.

Building Permit Fees in Cut and Shoot

Residential (1–2 family): New home

tiered rates by sq ft (Printed band total: permit, $50 base and plan review)‡

Up to 999 sq ft

$770.00

Over 999, up to 1,499 sq ft

$1,084.00

Over 1,499, up to 1,999 sq ft

$1,369.00

Over 1,999, up to 2,499 sq ft

$1,624.00

Over 2,499, up to 2,999 sq ft

$1,849.00

Over 2,999, up to 3,499 sq ft

$2,044.00

Over 3,499, up to 3,999 sq ft

$2,209.00

Over 3,999, up to 4,499 sq ft

$2,344.00

Over 4,499, up to 4,999 sq ft

$2,450.00

Over 4,999, up to 5,499 sq ft

$2,607.00

Over 5,499, up to 5,999 sq ft

$2,750.00

Over 5,999, up to 6,499 sq ft

$2,877.00

Over 6,499, up to 6,999 sq ft

$2,990.00

Over 6,999, up to 7,499 sq ft

$3,087.00

Over 7,499, up to 7,999 sq ft

$3,170.00

Over 7,999, up to 8,499 sq ft

$3,237.00

Over 8,499, up to 8,999 sq ft

$3,290.00

Over 8,999, up to 9,999 sq ft

$3,500.00

Over 9,999, up to 11,000 sq ft

$3,800.00

Residential (1–2 family): Residential fence (inspection included)

tiered rates by linears

Up to 100 linears

$75.00

Over 100 linears

$75.00 plus $15.00 per additional 100 linears

Residential (1–2 family): Manufactured home installation (occupancy permit, plus foundation strapping and skirting inspections)

$100.00 flat

Commercial / 3+ units: Commercial new building, addition, alteration or build-out (by valuation)

tiered rates by job value

Up to $1,000

$75.00

Over $1,000, up to $50,000

$200.00 plus $5.00 per additional $1,000

Over $50,000, up to $100,000

$445.00 plus $4.00 per additional $1,000

Over $100,000, up to $500,000

$645.00 plus $3.00 per additional $1,000

Over $500,000

$1,845.00 plus $2.00 per additional $1,000

Commercial / 3+ units: Commercial fence (inspection included)

tiered rates by linears

Up to 50 linears

$75.00

Over 50 linears

$75.00 plus $30.00 per additional 50 linears

Demolition of a building or structure (plus sewer disconnect fee)

tiered rates by sq ft

Up to 999 sq ft

$75.00

Over 999, up to 5,000 sq ft

$150.00

Over 5,000 sq ft

$300.00

Dumpster or trash enclosure built without a building permit (inspection included)

$115.00 flat

Residential or commercial generator (building permit, review included)

$350.00 flat

Swimming pool or spa (building permit, review included)

$450.00 flat

City Administrative Charge (does not apply to some listed rules)

10% of the permit fee (10% of each fee charged, including plan review and base fees)‡

Manufactured Home Foundation Strapping Inspection (select fee rules only)

$150.00

Manufactured Home Skirting Inspection (select fee rules only)

$150.00

Plan Review Fee (select fee rules only)

50% of the permit fee, jobs over $1,000 only

Sewer Disconnect Fee (demolition) (select fee rules only)

$75.00‡

Additional Inspection (building, site development or miscellaneous) (if applicable)

$75.00

Certificate of Occupancy When None Was Previously Issued (if applicable)

$200.00

Change of Occupancy in Group Classification (if applicable)

$200.00

Expired Permit Renewal (if applicable)

50% of the permit fee

Plan Check, Third and Later Submittals (select fee rules only) (if applicable)

50% of designated fees (50% of the original plan review fee)

Re-inspection Fee (if applicable)

$75.00

Replacement or Duplicate Certificate of Occupancy (if applicable)

$60.00

Residential Certificate (CO or CC) on Owner or Lender Request (if applicable)

$60.00

Special Inspection, Weekday After Hours (if applicable)

$150.00

Special Inspection, Weekend or City Holiday (if applicable)

$225.00

‡ Awaiting confirmation from the jurisdiction.

Electrical Permit Fees in Cut and Shoot

Residential (1–2 family): Residential electrical, building up to 5,000 sq ft

$75.00 per inspection‡

Residential (1–2 family): Residential electrical, building over 5,000 sq ft

$100.00 per inspection‡

Residential (1–2 family): Residential meter loop or service

$100.00 flat

Commercial / 3+ units: Commercial electrical, building up to 5,000 sq ft

$75.00 per inspection‡

Commercial / 3+ units: Commercial electrical, building 5,001 to 10,000 sq ft

$100.00 per inspection‡

Commercial / 3+ units: Commercial electrical, building over 10,000 sq ft

$150.00 per inspection‡

Commercial / 3+ units: Parking lot light poles

tiered rates by poles

Up to 2 poles

$75.00

Over 2 poles

$75.00 plus $15.00 per additional pole

Electrical reconnection or turn on (per building, inspection included)

$75.00 flat

Electrical yard light (inspection included)

$75.00 flat

Generator (electrical ground, rough and final inspections)

$275.00 flat

Swimming pool or spa only (trench and final inspections)

$200.00 flat

Temporary power pole (inspection included)

$75.00 flat

City Administrative Charge

10% of the permit fee (10% of each fee charged, including plan review and base fees)‡

Trade Base Permit Fee (select fee rules only)

$50.00

Trade Base Permit Fee (itemized trade permits) (select fee rules only)

$50.00‡

Additional Inspection (building, site development or miscellaneous) (if applicable)

$75.00

Expired Permit Renewal (if applicable)

50% of the permit fee

Re-inspection Fee (if applicable)

$75.00

Special Inspection, Weekday After Hours (if applicable)

$150.00

Special Inspection, Weekend or City Holiday (if applicable)

$225.00

‡ Awaiting confirmation from the jurisdiction.

Plumbing Permit Fees in Cut and Shoot

Residential (1–2 family): Residential plumbing, building up to 5,000 sq ft

$75.00 per inspection‡

Residential (1–2 family): Residential irrigation (lawn sprinkler) system

$115.00 flat

Residential (1–2 family): Residential plumbing, building over 5,000 sq ft

$100.00 per inspection‡

Residential (1–2 family): Residential rehab of water or sewer lines, or gas line replacement

$75.00 flat

Commercial / 3+ units: Commercial plumbing, building up to 5,000 sq ft

$75.00 per inspection‡

Commercial / 3+ units: Commercial irrigation (lawn sprinkler) system (by coverage area)

tiered rates by sq ft

Up to 10,000 sq ft

$115.00

Over 10,000 sq ft

$115.00 plus $6.00 per additional 2,000 sq ft

Commercial / 3+ units: Commercial plumbing, building 5,001 to 10,000 sq ft

$100.00 per inspection‡

Commercial / 3+ units: Commercial plumbing, building over 10,000 sq ft

$150.00 per inspection‡

Commercial / 3+ units: Commercial rehab of water or sewer lines, or gas line replacement (by length)

tiered rates by linears

Up to 300 linears

$115.00

Over 300 linears

$180.00

Backflow prevention device (not new construction)

$75.00 flat

Disconnect and plug sanitary or storm sewer (e.g. before demolition)

$75.00 flat

Gas test or retest and GTO (not new construction)

$75.00 flat

Gas yard light (each)

$75.00 flat

Generator (fuel gas ground, rough and final inspections)

$275.00 flat

Grease trap, sampling well, interceptor or other special waste device

$115.00 flat

Sewer or storm manhole

$75.00 per manhole (sewer or storm)

Swimming pool or spa only (trench and final inspections)

$200.00 flat

Water heater replacement (inspections included)

$75.00 flat

City Administrative Charge

10% of the permit fee (10% of each fee charged, including plan review and base fees)‡

Trade Base Permit Fee (select fee rules only)

$50.00

Trade Base Permit Fee (itemized trade permits) (select fee rules only)

$50.00‡

Additional Inspection (building, site development or miscellaneous) (if applicable)

$75.00

Expired Permit Renewal (if applicable)

50% of the permit fee

Re-inspection Fee (if applicable)

$75.00

Special Inspection, Weekday After Hours (if applicable)

$150.00

Special Inspection, Weekend or City Holiday (if applicable)

$225.00

‡ Awaiting confirmation from the jurisdiction.

Sponsor This Page

Be the Featured Electrician in Cut and Shoot

Homeowners and contractors planning a project check Cut and Shoot electrical permit fees here first. One sponsor per trade, flat monthly rate.

Advertise on This Page

Cut and Shoot Permit Fee Calculator

Pick a permit type and adjust the job value. Total updates instantly, itemized below.

Permit type

Project type

Kind of work

Job type

8 documented rates for this permit type; pick the one that matches your job.

Inspections

inspections

110 inspections

Estimated electrical permit fee

$220.00

Included in this total

Electrical Permit Fee$150.00‡

2 inspections × $75.00 per inspection

Trade Base Permit Fee$50.00

City Administrative Charge$20.00‡

Total Estimate$220.00

‡ Awaiting confirmation from the jurisdiction.

Estimate only. Confirm with the Cut and Shoot building department before applying. Phone: (936) 264-3100. Permit fees only; excludes impact fees, utility connection charges, and other non-permit charges.

Sponsor This Page

Be the Featured Electrician in Cut and Shoot

Homeowners and contractors planning a project check Cut and Shoot electrical permit fees here first. One sponsor per trade, flat monthly rate.

Advertise on This Page

How to Apply for a Permit in Cut and Shoot

Fill out the City's Residential Permit Application (online form on the Building Permits page, or the downloadable PDF) or the Commercial Permit Application, and submit it with plans to the City office. Bureau Veritas reviews plans and performs inspections for the City. Every contractor must register with the City before working inside the city limits (Contractor Registration Form with a copy of the driver's license and state license). All fees are paid to the City before the permit is issued. Remodels and additions to existing homes do not need a city permit; call the City office with questions.

Source: Cut and Shoot application instructions

Building Department Contact

Phone: (936) 264-3100
Email: cs@cutandshoot.org
Address: 14391 Hwy 105 East, Conroe, TX 77306
Hours: Monday to Friday, 8 a.m. to 12 p.m. and 1 p.m. to 4:45 p.m.
Source: https://cutandshoot.org/city-secretary ; https://cutandshoot.org/contact-us

Cut and Shoot Permit Fee FAQs

How Much Does a Roofing Permit Cost in Cut and Shoot?

The roofing permit for a $20,000 residential re-roof runs $110.00, based on Cut and Shoot's sourced fee schedule.

How Are Permit Fees Calculated in Cut and Shoot?

Electrical and Plumbing permits are priced per inspection; Mechanical / HVAC permits are flat fees for the default job (Complete HVAC change-out or new system, inspections included), while new construction is priced per inspection; Roofing permits are flat fees. New construction is priced separately from remodel and alteration work; the calculator asks which kind of job yours is. Every rate comes straight from the sourced fee schedule above. Enter your job's details for an itemized total.

What Surcharges Are Added to Permits in Cut and Shoot?

On top of the base permit fee, the sourced schedule adds City Administrative Charge (10% of the permit fee (10% of each fee charged, including plan review and base fees)) and Plan Review Fee (50% of the permit fee, jobs over $1,000 only). Each is included in the estimates it applies to; the fee schedule above shows which permits and job types each one covers.

Where Do These Fees Come From?

Every figure on this page is sourced from City of Cut and Shoot Ordinance No. 135, Municipal Building Permit Inspection-Plan Review Fee Schedule (Exhibits A and B). See the official schedule. Last verified November 3, 2026.

Other Jurisdictions in Montgomery County

Jobs inside another city's limits are permitted by that city; unincorporated areas by the county.

Unincorporated Montgomery County ConroeCut and ShootMagnolia Montgomery Oak Ridge North Panorama Village Shenandoah Stagecoach Willis Woodloch

Cut and Shoot, TX Permit Fees (2026)

Cut and Shoot Permit Fee Schedule

Building Permit Fees in Cut and Shoot

Electrical Permit Fees in Cut and Shoot

Plumbing Permit Fees in Cut and Shoot

Mechanical / HVAC Permit Fees in Cut and Shoot

Roofing Permit Fees in Cut and Shoot

Cut and Shoot Permit Fee Calculator

How to Apply for a Permit in Cut and Shoot

Cut and Shoot Permit Fee FAQs

How Much Does a Roofing Permit Cost in Cut and Shoot?

How Are Permit Fees Calculated in Cut and Shoot?

What Surcharges Are Added to Permits in Cut and Shoot?

Where Do These Fees Come From?

Other Jurisdictions in Montgomery County

Get in Touch