FreeEvery fee straight from the official city and county fee schedules. No signup.

Angleton, TX Permit Fees (2026)

Building permit fees and building, electrical, plumbing, mechanical/HVAC, and roofing permit fees for Angleton, straight from the official fee schedule, with a free permit fee calculator below.

In Angleton, a building permit for a remodel runs $150.00 in permit fees, a $20,000 re-roof $90.00, a $10,000 HVAC change-out $60.00, and a whole-house repipe $90.00. Totals include the documented surcharges and minimum fees; where the schedule prices by unit, figures assume a 200 sq ft remodel area and a 15-fixture scope. Each figure is that single permit only: a job that combines trades, like a kitchen remodel with electrical and plumbing work, pays each applicable permit. Pick a project to load it in the calculator below.

Jump to Permit Fee Calculator
Source

Angleton Schedule of Fees (Exhibit A to Ordinance No. 20250226-004, adopted February 26, 2025)

Covers building, electrical, plumbing, mechanical/HVAC, and roofing permits.

Apply online at the Angleton permit portal, or call 979-849-4364.

How Angleton values a job: Commercial permits are priced on the value of the work, and the city uses at least $100 per square foot as that value.

Schedule effective February 26, 2025. Last verified: November 3, 2026

Angleton Permit Fee Schedule

Every documented rule for each permit type, straight from the official schedule.

Mechanical / HVAC Permit Fees in Angleton

Residential (1–2 family): HVAC replacement or repair
$30.00 flat
Residential (1–2 family): New home, whole HVAC system
$75.00 flat
Commercial / 3+ units: Install, alter, repair, or replace a commercial mechanical system
tiered rates by job value, minimum $27.50‡
Up to $1,000
$10.50
Over $1,000
$10.50 plus $2.00 per additional $1,000
Permit Processing Fee
$30.00
After-hours Inspection Fee (Commercial) (if applicable)
$120.00
After-hours Inspection Fee (Residential) (if applicable)
$35.00
Re-inspection Fee (Commercial) (if applicable)
$100.00
Re-inspection Fee (Residential) (if applicable)
$20.00

‡ Awaiting confirmation from the jurisdiction.

Sponsor This Page
Be the Featured HVAC Company in Angleton

Homeowners and contractors planning a project check Angleton mechanical / HVAC permit fees here first. One sponsor per trade, flat monthly rate.

Advertise on This Page

Angleton Permit Fee Calculator

Pick a permit type and adjust the job value. Total updates instantly, itemized below.

Permit type
Project type
Kind of work
Estimated mechanical / HVAC permit fee
$60.00
Included in this total
Mechanical / HVAC Permit Fee$30.00
$30.00 flat
Permit Processing Fee$30.00
Total Estimate$60.00

Estimate only. Confirm with the Angleton building department before applying. Apply online. Phone: 979-849-4364. Permit fees only; excludes impact fees, utility connection charges, and other non-permit charges.

Sponsor This Page
Be the Featured HVAC Company in Angleton

Homeowners and contractors planning a project check Angleton mechanical / HVAC permit fees here first. One sponsor per trade, flat monthly rate.

Advertise on This Page

How to Apply for a Permit in Angleton

Apply online through the MGO Connect permit portal; since December 2, 2024 the City of Angleton Development Services Department no longer accepts emailed or paper permit submittals.

Every building, trade, roof, pool, demolition and foundation permit carries a $30 processing fee in addition to the permit fee.

For help with the portal or a permit, call the Permit Department at 979-849-4364 extension 2105 or email permits@angleton.tx.us; for website issues, call the MGO Help Desk at 985-851-0760.

Source: Angleton application instructions

Apply online: Angleton permit portal
Building Department Contact
Phone
979-849-4364 x 2105
Address
121 S. Velasco Street, Angleton, TX 77515

Angleton Permit Fee FAQs

How Much Does a Building Permit Cost in Angleton?

The building permit for a residential remodel runs $150.00, assuming a 200 sq ft remodel area (the schedule prices per unit), including the documented surcharges and minimum fees. The estimate is built from Angleton's sourced fee schedule, and it covers the building permit alone; a job that combines trades pays each applicable permit. Calculate your job's value for an itemized total.

How Much Does a Roofing Permit Cost in Angleton?

The roofing permit for a $20,000 residential re-roof runs $90.00, based on Angleton's sourced fee schedule.

How Are Permit Fees Calculated in Angleton?

A residential building permit is $0.40 per sq ft. Electrical permits are priced per outlet; Plumbing permits are priced per fixture; Mechanical / HVAC and Roofing permits are flat fees. New construction is priced separately from remodel and alteration work; the calculator asks which kind of job yours is. Every rate comes straight from the sourced fee schedule above. Enter your job's details for an itemized total.

What Surcharges Are Added to Permits in Angleton?

On top of the base permit fee, the sourced schedule adds Plan Review Fee (50% of the permit fee). Each is included in the estimates it applies to; the fee schedule above shows which permits and job types each one covers.

Where Do These Fees Come From?

Every figure on this page is sourced from Angleton Schedule of Fees (Exhibit A to Ordinance No. 20250226-004, adopted February 26, 2025). See the official schedule. Last verified .

Other Jurisdictions in Brazoria County

Jobs inside another city's limits are permitted by that city; unincorporated areas by the county.

Contact

Get in Touch

Missing a jurisdiction? Spotted a fee that looks off? Request coverage for a city or county, report an issue, or ask about sponsorship. We typically reply within one business day.