FreeEvery fee straight from the official city and county fee schedules. No signup.

Taylor, TX Permit Fees (2026)

Building, electrical, plumbing, mechanical/HVAC, and roofing permit fees for Taylor, straight from the official fee schedule, with a free permit fee calculator below.

A note on these figures from the official schedule. Details

Properties inside a Neighborhood Empowerment Zone may qualify for a 50% reduction in building, electrical, plumbing, mechanical, foundation and roof permit fees (not for work started without a permit). Estimates show the full fee; ask the city whether your property qualifies.

In Taylor, a building permit for a remodel runs $250.00 in permit fees, a $20,000 re-roof $110.00, a $10,000 HVAC change-out $120.00, a $10,000 electrical panel upgrade or rewire $110.00, and a $10,000 whole-house repipe $110.00. Totals include the documented surcharges and minimum fees; where the schedule prices by unit, figures assume a 200 sq ft remodel area. Each figure is that single permit only: a job that combines trades, like a kitchen remodel with electrical and plumbing work, pays each applicable permit. Pick a project to load it in the calculator below.

Jump to Permit Fee Calculator
Source

City of Taylor FY 2027 Fee Schedule for City Services (Exhibit A to Ordinance 2026-29, adopted 9/24/2026, effective 10/1/2026), Development Services Fee Schedule

Covers building, electrical, plumbing, mechanical/HVAC, and roofing permits.

Apply online at the Taylor permit portal, or call 512-309-6701.

Schedule effective October 1, 2026. Last verified: November 20, 2026

Taylor Permit Fee Schedule

Every documented rule for each permit type, straight from the official schedule.

Building Permit Fees in Taylor

Residential (1–2 family): Residential remodel
$0.75 per sq ft (gross floor area)
Residential (1–2 family): New home or residential addition, including attached carport
$1.00 per sq ft (gross floor area)
Residential (1–2 family): Residential swimming pool, spa or sauna
$100.00 flat
Residential (1–2 family): Residential accessory structure, 200 sq ft or larger
$1.00 per sq ft (gross floor area)
Residential (1–2 family): Residential manufactured home
$0.50 per sq ft (gross floor area)
Commercial / 3+ units: Commercial remodel, including multifamily over 4 units and mixed use
$0.75 per sq ft (gross floor area)
Commercial / 3+ units: New commercial building or addition, including multifamily over 4 units and mixed use
$1.00 per sq ft (gross floor area)
Commercial / 3+ units: Commercial swimming pool
$250.00 flat

‡ Awaiting confirmation from the jurisdiction.

Sponsor This Page
Be the Featured General Contractor in Taylor

Homeowners and contractors planning a project check Taylor building permit fees here first.

One sponsor per trade, flat monthly rate.

Taylor Permit Fee Calculator

Pick a permit type and adjust the job value. Total updates instantly, itemized below.

Permit type
Project type
Kind of work
Job type

6 documented rates for this permit type; pick the one that matches your job.

sq ft
505,000 sq ft
Estimated building permit fee
$250.00
Included in this total
Building Permit Fee$150.00
200 sq ft (gross floor area) × $0.75 per sq ft (gross floor area)
Plan Review Fee (Residential Remodel or Manufactured Home)$75.00
Technology Fee$25.00
Total Estimate$250.00
Not included in this total
Re-Inspection Fee (Residential)$55.00 / inspection
Charged per inspection; depends on your project's number of inspections.
A note on these figures from the official schedule. Details

Properties inside a Neighborhood Empowerment Zone may qualify for a 50% reduction in building, electrical, plumbing, mechanical, foundation and roof permit fees (not for work started without a permit). Estimates show the full fee; ask the city whether your property qualifies.

Estimate only. Confirm with the Taylor building department before applying. Apply online. Phone: 512-309-6701. Permit fees only; excludes impact fees, utility connection charges, and other non-permit charges.

Sponsor This Page
Be the Featured General Contractor in Taylor

Homeowners and contractors planning a project check Taylor building permit fees here first.

One sponsor per trade, flat monthly rate.

How to Apply for a Permit in Taylor

Apply online through the City of Taylor's My Government Online (MGO) Connect customer portal: create an account, register as a contractor (free of charge), and submit the permit application with the required documents as PDFs. The city assesses the application fee once staff accepts the application; pay it when notified or the application is voided. Plan review fees are collected at application and permit fees upon permit approval.

Request inspections through the same MGO portal; requests submitted by 3 pm get next business day service.

If you are unsure whether you need a permit, email permits@taylortx.gov before starting work.

Source: Taylor application instructions

Apply online: Taylor permit portal
Building Department Contact
Address
400 Porter St, Taylor, TX 76574
Sponsor This Spot · Permit Help
Be the Featured Permit Expediter in Williamson County

Your name, phone and website right here, next to the building department's contact info, where people look right before they apply.

One expediter per county.

Taylor Permit Fee FAQs

How Much Does a Building Permit Cost in Taylor?

The building permit for a residential remodel runs $250.00, assuming a 200 sq ft remodel area (the schedule prices per unit), including the documented surcharges and minimum fees. The estimate is built from Taylor's sourced fee schedule, and it covers the building permit alone; a job that combines trades pays each applicable permit. Calculate your job's value for an itemized total.

How Much Does a Roofing Permit Cost in Taylor?

The roofing permit for a $20,000 residential re-roof runs $110.00, based on Taylor's sourced fee schedule.

How Are Permit Fees Calculated in Taylor?

A residential building permit is $0.75 per sq ft (gross floor area). Electrical, Plumbing, Mechanical / HVAC, and Roofing permits are flat fees. New construction is priced separately from remodel and alteration work; the calculator asks which kind of job yours is. Every rate comes straight from the sourced fee schedule above. Enter your job's details for an itemized total.

Where Do These Fees Come From?

Every figure on this page is sourced from City of Taylor FY 2027 Fee Schedule for City Services (Exhibit A to Ordinance 2026-29, adopted 9/24/2026, effective 10/1/2026), Development Services Fee Schedule. See the official schedule. Last verified .

Other Jurisdictions in Williamson County

Jobs inside another city's limits are permitted by that city; unincorporated areas by the county.

Contact

Get in Touch

Missing a jurisdiction? Spotted a fee that looks off? Request coverage for a city or county, report an issue, or ask about sponsorship. We typically reply within one business day.